To turn a cabinet parts list into cut diagrams and labels, put one row per part in a spreadsheet with an ID, length, width, quantity, material and grain direction, list your stock sheets separately, and run both through a cut list optimizer that accounts for saw kerf, edge trim and grain. Print a diagram for each sheet with a numbered cut sequence and a label for every piece. When the client revises after cutting has started, compare the new parts list with the old one by part ID, keep the pieces that are already cut and unchanged, recut only what changed, and set aside what was removed.
This guide covers what goes in a cut list, how to prepare the spreadsheet, the numbers that matter, how to estimate sheets, how guillotine layouts work, how to label parts and how to handle a revision. It links to the deeper guides on this site. The examples are illustrative, not a tested cabinet design: always check layouts, dimensions and your shop’s construction method before you cut.
What is a cut list, and what goes in one?
Three documents get called a cut list, and keeping them apart avoids confusion:
| Document | What it is | Who uses it |
|---|---|---|
| Parts list | Every part the job needs, with its finished size, quantity, material and grain | The designer or estimator |
| Cut list | Every piece the saw makes, grouped by sheet, in cutting order | The saw operator |
| Cutting diagram | A drawing of each sheet with every piece in place and the cut order | The saw operator |
A useful parts list row includes:
- Part ID, unique across the job, such as
K1-SIDE-L. - Name, such as “Sink base left side”.
- Length and width, in one unit throughout.
- Quantity.
- Material, matching the name in your stock list exactly.
- Grain direction: along the length, along the width, or none.
- Notes, such as edge banding.
Cut list terms explained: kerf, trim, grain and more is a glossary of the rest.
How do I prepare a parts spreadsheet for cutting?
Most small shops already do the cabinet math in a spreadsheet. A few habits make that sheet ready for an optimizer without retyping.
- One row per part type, with a quantity column, rather than one row per piece.
- Give every part a unique ID that will stay the same across revisions. This is what lets you compare revisions later.
- Use one unit system per file. Millimetres, decimal inches or fractions, but not a mix. A mixed file is the most common source of a part cut to the wrong size.
- Decide finished size or cut size. If parts get edge banding, decide whether your sizes include the band and be consistent.
- Match material names to your stock list exactly: “18mm Maple Ply” and “18 mm maple ply” may be treated as different materials.
- Fill in grain for every part on grained stock.
- Make a stock sheet listing each material, its sheet length and width, quantity on hand and whether it has grain.
- Save both as CSV for import.
The full walkthrough is in how to make a cabinet cut list from a spreadsheet. If you design in SketchUp, the free OpenCutList extension can export a parts list; see OpenCutList CSV export to CutPacket, step by step.
Kerf, edge trim and grain: the numbers that matter
Kerf is the width of material the blade removes on each cut. Panel saw and table saw blades are commonly around 3 mm, often quoted as 1/8 in. It sounds small, but across a row of parts it adds up: five 100 mm strips need 500 mm of material plus a kerf between each pair. Ignore kerf and the last part comes up short.
Edge trim is the strip taken off factory edges, which are often chipped or not square. A typical trim is 10 mm or so per edge, and it shrinks the usable sheet. A 2440 by 1220 mm sheet with 10 mm trimmed from every edge leaves 2420 by 1200 mm to work with.
Grain direction decides which way a part can be placed. A cabinet side in veneered plywood normally has grain running vertically, so it cannot be rotated to fit a gap. Melamine and MDF usually have no grain, so parts can rotate freely. Grain is often the biggest reason a layout needs more sheets than the area suggests.
How many sheets will a job need?
The quick estimate is the area method:
- Multiply length by width for each part, then by its quantity.
- Add the areas for one material.
- Divide by the area of one sheet. A 4 by 8 ft sheet is 48 by 96 in, which is 4,608 sq in or 32 sq ft.
- Round up.
For example, if the box parts in 3/4 in plywood add up to 80 sq ft, that is 2.5 sheets, so at least 3. This is a lower bound, not an order. Kerf, trim, grain and part sizes that do not nest well can push the real count higher, which is why a layout is the better way to decide what to buy. How many sheets of plywood for kitchen cabinets? works through a fuller example.
How are guillotine layouts optimized?
Most small shops cut sheet goods on a panel saw, table saw or sliding table saw. These saws make straight cuts from one edge of a panel to the other, called guillotine cuts. A layout that a CNC router could cut, with parts nested in irregular shapes, may be impossible on a saw.
A guillotine layout is built in stages:
- First cuts divide the sheet into strips, often rips along the length.
- Second cuts divide each strip into pieces, usually crosscuts.
- Further cuts trim pieces from the remaining parts of a strip, if needed.
Optimizers search for layouts that use fewer sheets while respecting kerf, trim and grain and keeping every cut a straight edge-to-edge cut. Finding the absolute best layout is a hard mathematical problem, so practical tools use heuristics that find very good layouts quickly. A useful property for a shop is determinism: the same input gives the same layout, so a reprint matches what is already on the cart.
The cut sequence matters as much as the layout. A numbered sequence on each diagram tells the operator which cut comes first, so the right strips come off before they are crosscut.
How should cabinet parts be labeled?
Once a sheet is cut, the pieces lose their context. A stack of white melamine rectangles all looks the same. Labels restore it.
A good part label shows:
- The job and cabinet, such as
Hartley K1. - The part ID and name.
- The finished length and width.
- The material.
- A grain arrow, where it matters.
- Edge banding notes, if your shop uses them.
Labels are commonly printed on sheets of address labels, such as the Avery 5163 size, which is 2 by 4 in, 10 per page, or on a dedicated label printer from a CSV file. Apply each label as the piece comes off the saw, on a face that will not show or will be cleaned.
What do I do when the client revises after some parts are cut?
Revisions after cutting has started are normal in small cabinet work. A client sees the layout taped out on the floor and wants the sink base wider; a drawer bank goes because an appliance moved. The material is rarely the costly part. The confusion is: which of the stacked panels are still right?
- Pause the saw and record which pieces are already cut.
- Compare the revised parts list with the old one by part ID. For each part, decide whether it is new, changed in size, material or grain, increased or decreased in quantity, removed, or unchanged.
- Sort every piece into piles: cut new, recut and scrap the old, cut as planned, keep (already cut and unchanged) and surplus (cut but no longer needed).
- Re-plan only what is needed. Kept pieces should use no new stock.
- Print new labels only for new and recut pieces, so old and new labels never mix on the cart.
- Mark scrap clearly so an old piece is not used by mistake.
Cabinet order changed after cutting? A recut checklist covers each step in detail.
Cut list software for small shops
| Option | Cost model | Good for | Watch for |
|---|---|---|---|
| Spreadsheet and pencil | Free | Small jobs, one-off projects | Slow; no layout checking |
| OpenCutList (SketchUp extension) | Free, open source | Shops that model in SketchUp; parts lists, diagrams and labels from the model | Needs SketchUp |
| Online cut list optimizers | Free and paid tiers | Quick layouts in the browser | Check where job data goes and how revisions are handled |
| Cabinet design suites | Licence or subscription | Shops that design, quote and cut in one system | More than a small shop may need |
| CutPacket | One-time purchase, with a free trial | Spreadsheet-based shops that need diagrams, labels and recut lists | Rectangular parts and guillotine layouts only |
If a free tool’s diagrams do everything your shop needs, keep using it. The deciding question for most small shops is what happens when the client revises the order after cutting starts.
How CutPacket fixes this
CutPacket is a Windows desktop app for small cabinet and furniture shops that turns a parts list, or a revised one, into a shop-floor packet.
- Revision compare. Import the revised parts CSV. It compares by part ID and flags each part as new, changed (size, material or grain), quantity up, quantity down, removed or unchanged. Already-cut unchanged pieces are kept and use no new stock; changed pieces are recut with the old one marked as scrap; removed pieces become surplus. Labels for kept pieces are not reprinted.
- Outputs. Cut diagrams as PDF, one landscape page per sheet with a numbered cut sequence; labels as PDF on an Avery 5163-compatible 4 x 2 in grid, 10 per page, plus a CSV for label printers; a recut list as PDF and CSV.
- Validation first. Mixed units in one file are refused, never silently converted. Parts that cannot fit any sheet after edge trim are blocked, blank grain on grained stock is blocked, and duplicate IDs and bad numbers are reported with row numbers.
- Guillotine optimizer. Rectangular layouts cut with straight edge-to-edge saw cuts, respecting kerf, edge trim and grain, never using more sheets than you have on hand. The same input gives the same layout.
- Review before you cut. Approve each sheet before export, pin sheets to keep their layout, and mark sheets or pieces as already cut.
- Inputs. Parts and stock CSV files with flexible headers, in millimetres or inches, with fractions such as 24 1/2 accepted. Your source CSVs are never modified.
- Local. No account, no cloud and no telemetry. Each export goes to its own folder.
Good to know: always check layouts and dimensions before you cut.
CutPacket has a free trial on the Microsoft Store, then a one-time purchase.
Get CutPacket from the Microsoft Store
Frequently asked questions
What columns should a cabinet parts spreadsheet have?
Part ID, name, length, width, quantity, material and grain direction, plus optional notes. Use one unit system per file.
How much should I allow for saw kerf?
Use your blade’s actual width. Panel saw and table saw blades are commonly around 3 mm, often quoted as 1/8 in.
How do I estimate how many sheets a job needs?
Add up part areas, divide by the sheet area and round up. Treat it as a minimum, since kerf, trim and grain add waste.
What should I do with parts already cut when the order changes?
Compare the revised list with the old one by part ID. Keep unchanged cut pieces, recut changed ones and set removed ones aside as surplus.